Prisma Access
Riverbed SteelConnect SD-WAN Solution Guide
Table of Contents
Expand All
|
Collapse All
Prisma Access Docs
-
-
- Prisma Access China
- 4.0 & Later
- 3.2 Preferred and Innovation
- 3.1 Preferred and Innovation
- 3.0 Preferred and Innovation
- 2.2 Preferred
-
-
-
- 5.2 Preferred and Innovation
- 5.1 Preferred and Innovation
- 5.0 Preferred and Innovation
- 4.2 Preferred
- 4.1 Preferred
- 4.0 Preferred
- 3.2 Preferred and Innovation
- 3.1 Preferred and Innovation
- 3.0 Preferred and Innovation
- 2.2 Preferred
Riverbed SteelConnect SD-WAN Solution Guide
Where Can I Use This? | What Do I Need? |
---|---|
|
|
To use this Solution Guide, you need a knowledge of the following software and hardware
concepts:
- SD-WAN routing principles
- SteelConnect Manager (SCM)
- SteelConnect appliances (in particular, SteelConnect gateways)
- Panorama appliance configuration tasks
- Prisma Access configuration tasks
Supported IKE and IPSec Cryptographic Profiles
Prisma Access supports standard IPSec tunnels from third-party SD-WAN edge devices
using IKE and IPSec Crypto profiles.
The following table documents the IKE/IPSec crypto settings that are supported with
Prisma Access and SteelConnect SD-WAN.
A check mark indicates that the profile or architecture type is supported; a dash (—)
indicates that it's not supported. Default and Recommended settings are noted in the
table.
Crypto Profiles | Prisma Access | SteelConnect SD-WAN | |
---|---|---|---|
Tunnel Type | IPSec Tunnel |
|
|
GRE Tunnel | — | — | |
Routing | Static Routes |
|
|
Dynamic Routing (BGP) |
|
| |
Dynamic Routing (OSPF) | — |
| |
IKE Versions | IKE v1 |
|
|
IKE v2 |
|
| |
IPSec Phase 1 DH-Group | Group 1 |
|
|
Group 2 |
| ||
Group 5 |
|
| |
Group 14 |
|
| |
Group 19 |
| — | |
Group 20 | — | ||
IPSec Phase 1 Auth If you use
IKEv2 with certificate-based authentication, only SHA1 is
supported in IKE crypto profiles (Phase 1). | MD5 |
|
|
SHA1 |
| ||
SHA256 |
|
| |
SHA384 |
|
| |
SHA512 |
| ||
IPSec Phase 1 Encryption | DES |
| — |
3DES |
| ||
AES-128-CBC | |||
AES-192-CBC |
|
| |
AES-256-CBC |
| ||
IPSec Phase 1 Key Lifetime Default | |||
IPSec Phase 1 Peer Authentication | Pre-Shared Key |
|
|
Certificate |
|
| |
IKE Peer Identification | FQDN |
|
|
IP Address |
|
| |
User FQDN |
| — | |
IKE Peer | As Static Peer |
|
|
As Dynamic Peer |
|
| |
Options | NAT Traversal |
|
|
Passive Mode |
| — | |
Ability to Negotiate Tunnel | Per Subnet Pair |
|
|
Per Pair of Hosts |
|
| |
Per Gateway Pair |
| — | |
IPSec Phase 2 DH-Group | Group 1 |
|
|
Group 2 | |||
Group 5 |
|
| |
Group 14 |
|
| |
Group 19 |
| — | |
Group 20 | — | ||
No PFS |
| — | |
IPSec Phase 2 Auth | MD5 |
|
|
SHA1 |
| ||
SHA256 |
|
| |
SHA384 |
|
| |
SHA512 | |||
None |
| — | |
IPSec Phase 2 Encryption | DES |
| — |
3DES |
| ||
AES-128-CBC |
| ||
AES-192-CBC |
|
| |
AES-256-CBC |
| ||
AES-128-CCM |
| — | |
AES-128-GCM |
| — | |
AES-256-GCM |
| ||
NULL |
|
| |
IPSec Protocol | ESP |
|
|
AH |
| — | |
IPSec Phase 2 Key Lifetime Default | |||
Tunnel Monitoring Fallback | Dead Peer Detection (DPD) |
| — |
ICMP | — | — | |
Bidirectional Forwarding Detection (BFD) | — | — | |
SD-WAN Architecture Type | With Regional Hub/Gateway/Data Center | NA |
|
No Regional Hub/Gateway/Data Center | NA |
|
SD-WAN Deployment Architectures Supported by Riverbed
Riverbed supports the following deployment architectures for use with Prisma Access.
A dash (—) indicates that the deployment isn't supported.
Use Case | Architecture | Supported? |
---|---|---|
Securing traffic from each branch site with 1 WAN
link (Type 1) Use an IPSec tunnel from each branch to Prisma
Access. Use a Riverbed SD-WAN appliance device at the
branch. | Yes | |
Securing branch and HQ sites with active/backup SD-WAN connections | No | |
Securing branch and HQ sites with active/active SD-WAN connections | No | |
Securing branch and HQ sites with SD-WAN edge devices in HA mode | Yes | |
Securing SD-WAN deployments with Regional Hub/POP architecture (Type 2) | Yes |