Prisma Access
Silver Peak SD-WAN Solution Guide
Table of Contents
Expand All
|
Collapse All
Prisma Access Docs
-
-
- Prisma Access China
- 4.0 & Later
- 3.2 Preferred and Innovation
- 3.1 Preferred and Innovation
- 3.0 Preferred and Innovation
- 2.2 Preferred
-
-
-
- 5.2 Preferred and Innovation
- 5.1 Preferred and Innovation
- 5.0 Preferred and Innovation
- 4.2 Preferred
- 4.1 Preferred
- 4.0 Preferred
- 3.2 Preferred and Innovation
- 3.1 Preferred and Innovation
- 3.0 Preferred and Innovation
- 2.2 Preferred
Silver Peak SD-WAN Solution Guide
| Where Can I Use This? | What Do I Need? |
|---|---|
|
|
You onboard your SD-WAN edge devices using a remote network connection between the edge
device at the branch site, HQ, or hub to Prisma Access. Use Prisma Access to create a
remote network and configure IPSec and IKE Crypto profiles; then, set up an IPSec tunnel
between the SD-WAN edge device and Prisma Access, using the same crypto profiles you
used in Prisma Access.
The following table documents the IKE/IPSec crypto settings that are supported with
Prisma Access and Silver Peak SD-WAN. A check mark indicates that the profile or
architecture type is supported; a dash (—) indicates that it's not supported. Default
and Recommended settings are noted in the table.
| Crypto Profiles | Prisma Access | Silver Peak EdgeConnect | |
|---|---|---|---|
| Tunnel Type | IPSec Tunnel |
√
|
√
|
| GRE Tunnel | — | — | |
| Routing | Static Routes |
√
|
√
|
| Dynamic Routing (BGP) |
√
| — | |
| Dynamic Routing (OSPF) | — | — | |
| IKE Versions | IKE v1 |
√
|
√
|
| IKE v2 |
√
| — | |
| IPSec Phase 1 DH-Group | Group 1 |
√
|
√
|
| Group 2 | √ (Default) |
√
| |
| Group 5 |
√
|
√
| |
| Group 14 |
√
| √ (Recommended) | |
| Group 19 |
√
|
√
| |
| Group 20 | √ (Recommended) | — | |
| IPSec Phase 1 Auth If you use IKEv2
with certificate-based authentication, only SHA1 is supported in IKE
crypto profiles (Phase 1). | MD5 |
√
| — |
| SHA1 | √ (Default) | √ (Recommended) | |
| SHA256 |
√
|
√
| |
| SHA384 |
√
|
√
| |
| SHA512 | √ (Recommended) |
√
| |
| IPSec Phase 1 Encryption | DES |
√
| — |
| 3DES | √ (Default) | — | |
| AES-128-CBC | √ (Default) |
√
| |
| AES-192-CBC |
√
| — | |
| AES-256-CBC | √ (Recommended) | √ (Recommended) | |
| IPSec Phase 1 Key Lifetime Default | √ (8 Hours) | √ (8 Hours Recommended) | |
| IPSec Phase 1 Peer Authentication | Pre-Shared Key |
√
| Pre-Shared Key |
| Certificate |
√
| — | |
| IKE Peer Identification | FQDN |
√
|
√
|
| IP Address |
√
|
√
| |
| User FQDN |
√
|
√
| |
| IKE Peer | As Static Peer |
√
|
√
|
| As Dynamic Peer |
√
| — | |
| Options | NAT Traversal |
√
|
√
|
| Passive Mode |
√
| — | |
| Ability to Negotiate Tunnel | Per Subnet Pair |
√
| — |
| Per Pair of Hosts |
√
| — | |
| Per Gateway Pair |
√
|
√
| |
| IPSec Phase 2 DH-Group | Group 1 |
√
|
√
|
| Group 2 | √ (Default) |
√
| |
| Group 5 |
√
|
√
| |
| Group 14 |
√
| √ (Recommended) | |
| Group 19 |
√
|
√
| |
| Group 20 | √ (Recommended) | — | |
| No PFS |
√
|
√
| |
| IPSec Phase 2 Auth | MD5 |
√
| — |
| SHA1 | √ (Default) |
√
| |
| SHA256 |
√
| √ (Recommended) | |
| SHA384 |
√
|
√
| |
| SHA512 | √ (Recommended) |
√
| |
| None |
√
| — | |
| IPSec Phase 2 Encryption | DES |
√
| — |
| 3DES | √ (Default) | — | |
| AES-128-CBC | √ (Default) |
√
| |
| AES-192-CBC |
√
| — | |
| AES-256-CBC |
√
| √ (Recommended) | |
| AES-128-CCM |
√
| — | |
| AES-128-GCM |
√
| — | |
| AES-256-GCM | √ (Recommended) | — | |
| NULL |
√
|
√
| |
| IPSec Protocol | ESP |
√
|
√
|
| AH |
√
| — | |
| IPSec Phase 2 Key Lifetime Default | √ (1 Hour) | √ (Recommended 1 HourLifebytes also
supported | |
| Tunnel Monitoring Fallback | Dead Peer Detection (DPD) |
√
|
√
|
| ICMP | — | √ (HTTP GET also supported) | |
| Bidirectional Forwarding Detection (BFD) | — | — | |
| SD-WAN Architecture Type | With Regional Hub/Gateway/Data Center | N/A |
√
|
| No Regional Hub/Gateway/Data Center | NA |
√
| |