Focus

PAN-OS CLI Quick Start

CLI Cheat Sheet: User-ID

Table of Contents

CLI Cheat Sheet: User-ID

Use the following commands to perform common User-ID configuration and monitoring tasks.

To see more comprehensive logging information enable debug mode on the agent using the debug user-id log-ip-user-mapping yes command. When you are done troubleshooting, disable debug mode using debug user-id log-ip-user-mapping no.

CLI Cheat Sheet: User-ID
View all User-ID agents configured to send user mappings to the Palo Alto Networks device: To see all configured Windows-based agents: > show user user-id-agent state all To see if the PAN-OS-integrated agent is configured: > show user server-monitor state all
View how many log messages came in from syslog senders and how many entries the User-ID agent successfully mapped: > show user server-monitor statistics
View the configuration of a User-ID agent from the Palo Alto Networks device: > show user user-id-agent config name `<agent-name>`
View group mapping information: > show user group-mapping statistics > show user group-mapping state all > show user group list > show user group name `<group-name>`
View all user mappings on the Palo Alto Networks device: > show user ip-user-mapping all Show user mappings filtered by a username string (if the string includes the domain name, use two backslashes before the username): > show user ip-user-mapping all \| match `<domain>`\\`<username-string>` Show user mappings for a specific IP address: > show user ip-user-mapping ip `<ip-address>` Show usernames: > show user user-ids
View the most recent addresses learned from a particular User-ID agent: > show log userid datasourcename equal `<agent-name>` direction equal backward
View mappings from a particular type of authentication service: > show log userid datasourcetype equal `<authentication-service>` where `<authentication-service>` can be authenticate, client-cert, directory-server, exchange-server, globalprotect, kerberos, netbios-probing, ntlm, unknown, vpn-client, or wmi-probing. For example, to view all user mappings from the Kerberos server, you would enter the following command: > show log userid datasourcetype equal kerberos
View mappings learned using a particular type of user mapping: > show log userid datasource equal `<datasource>` where `<datasource>` can be agent, captive-portal, event-log, ha, probing, server-session-monitor, ts-agent, unknown, vpn-client, or xml-api. For example, to view all user mappings from the XML API, you would enter the following command: > show log userid datasourcetype equal xml-api
Find a user mapping based on an email address: > show user email-lookup + base Default base distinguished name (DN) to use for searches + bind-dn bind distinguished name + bind-password bind password + domain Domain name to be used for username + group-object group object class(comma-separated) + name-attribute name attribute + proxy-agent agent ip or host name. + proxy-agent-port user-id agent listening port, default is 5007 + use-ssl use-ssl * email email address > mail-attribute mail attribute > server ldap server ip or host name. > server-port ldap server listening port For example: > show user email-lookup base "DC=lab,DC=sg,DC=acme,DC=local" bind-dn "CN=Administrator,CN=Users,DC=lab,DC=sg,DC=acme,DC=local" bind-password acme use-ssl no email user1@lab.sg.acme.local mail-attribute mail server 10.1.1.1 server-port 389 labsg\user1
Clear the User-ID cache: clear user-cache all Clear a User-ID mapping for a specific IP address: clear user-cache ip `<ip-address/netmask>`

CLI Cheat Sheet: User-ID

View all User-ID agents configured to send user mappings to the Palo Alto Networks device:

To see all configured Windows-based agents:

> show user user-id-agent state all

To see if the PAN-OS-integrated agent is configured:

> show user server-monitor state all

View how many log messages came in from syslog senders and how many entries the User-ID agent successfully mapped:

> show user server-monitor statistics

View the configuration of a User-ID agent from the Palo Alto Networks device:

> show user user-id-agent config name <agent-name>

View group mapping information:

> show user group-mapping statistics 
> show user group-mapping state all 
> show user group list 
> show user group name <group-name>

View all user mappings on the Palo Alto Networks device:

> show user ip-user-mapping all

Show user mappings filtered by a username string (if the string includes the domain name, use two backslashes before the username):

> show user ip-user-mapping all | match <domain>\\<username-string>

Show user mappings for a specific IP address:

> show user ip-user-mapping ip <ip-address>

Show usernames:

> show user user-ids

View the most recent addresses learned from a particular User-ID agent:

> show log userid datasourcename equal <agent-name> direction equal backward

View mappings from a particular type of authentication service:

> show log userid datasourcetype equal <authentication-service>

where <authentication-service> can be authenticate, client-cert, directory-server, exchange-server, globalprotect, kerberos, netbios-probing, ntlm, unknown, vpn-client, or wmi-probing.

For example, to view all user mappings from the Kerberos server, you would enter the following command:

> show log userid datasourcetype equal kerberos

View mappings learned using a particular type of user mapping:

> show log userid datasource equal <datasource>

where <datasource> can be agent, captive-portal, event-log, ha, probing, server-session-monitor, ts-agent, unknown, vpn-client, or xml-api.

For example, to view all user mappings from the XML API, you would enter the following command:

> show log userid datasourcetype equal xml-api

Find a user mapping based on an email address:

> show user email-lookup 
+ base               Default base distinguished name (DN) to use for searches 
+ bind-dn            bind distinguished name 
+ bind-password      bind password 
+ domain             Domain name to be used for username 
+ group-object       group object class(comma-separated) 
+ name-attribute     name attribute 
+ proxy-agent        agent ip or host name. 
+ proxy-agent-port   user-id agent listening port, default is 5007 
+ use-ssl            use-ssl 
* email              email address 
> mail-attribute     mail attribute 
> server             ldap server ip or host name. 
> server-port        ldap server listening port

For example:

> show user email-lookup base "DC=lab,DC=sg,DC=acme,DC=local" bind-dn "CN=Administrator,CN=Users,DC=lab,DC=sg,DC=acme,DC=local" bind-password acme use-ssl no email user1@lab.sg.acme.local mail-attribute mail server 10.1.1.1 server-port 389 labsg\user1

Clear the User-ID cache:

clear user-cache all

Clear a User-ID mapping for a specific IP address:

clear user-cache ip <ip-address/netmask>

CLI Cheat Sheet: Device Management

CLI Cheat Sheet: HA