Configure Multicast
Table of Contents
Expand all | Collapse all
-
-
- Add a Branch
- Add a Data Center
- Add a Branch Gateway
- Configure Circuits
- Configure Internet Circuit Underlay Link Aggregation
- Configure Private WAN Underlay Link Quality Aggregation
- Configure Circuit Categories
- Configure Device Initiated Connections for Circuits
- Add Public IP LAN Address to Enterprise Prefixes
- Manage Data Center Clusters
- Configure a Site Prefix
- Configure a DHCP Server
- Configure NTP for Prisma SD-WAN
- Configure the ION Device at a Branch Site
- Configure the ION Device at a Data Center
- Switch a Site to Control Mode
- Allow IP Addresses in Firewall Configuration
-
- Configure a Controller Port
- Configure Internet Ports
- Configure WAN/LAN Ports
- Configure a Loopback Interface
- Configure a PoE Port
- Configure and Monitor LLDP Activity and Status
- Configure a PPPoE Interface
- Configure a Layer 3 LAN Interface
- Configure Application Reachability Probes
- Configure a Secondary IP Address
- Configure a Static ARP
- Configure a DHCP Relay
- Configure IP Directed Broadcast
- VPN Keep-Alives
-
- Configure Prisma SD-WAN IPFIX
- Configure IPFIX Profiles and Templates
- Configure and Attach a Collector Context to a Device Interface in IPFIX
- Configure and Attach a Filter Context to a Device Interface in IPFIX
- Configure Global and Local IPFIX Prefixes
- Flow Information Elements
- Options Information Elements
- Configure the DNS Service on the Prisma SD-WAN Interface
- Configure SNMP
-
-
- Prisma SD-WAN Branch Routing
- Prisma SD-WAN Data Center Routing
-
- Configure Multicast
- Create a WAN Multicast Configuration Profile
- Assign WAN Multicast Configuration Profiles to Branch Sites
- Configure a Multicast Source at a Branch Site
- Configure Global Multicast Parameters
- Configure a Multicast Static Rendezvous Point (RP)
- Learn Rendezvous Points (RPs) Dynamically
- View LAN Statistics for Multicast
- View WAN Statistics for Multicast
- View IGMP Membership
- View the Multicast Route Table
- View Multicast Flow Statistics
- View Routing Statistics
- Prisma SD-WAN Incident Policies
-
- Prisma SD-WAN Branch HA Key Concepts
- Configure Branch HA
- Configure HA Groups
- Add ION Devices to HA Groups
- View Device Configuration of HA Groups
- Edit HA Groups and Group Membership
-
- Configure Branch HA with Gen-1 Platforms (2000, 3000, 7000, and 9000)
- Configure Branch HA with Gen-2 Platforms (3200, 5200, and 9200)
- Configure Branch HA with Gen-2 Embedded Switch Platforms (1200-S or 3200-L2)
- Configure Branch HA for Devices with Software Cellular Bypass (1200-S-C-5G)
- Configure Branch HA for Platforms without Bypass Pairs
- Prisma SD-WAN Clarity Reports
- Prisma SD-WAN Incidents and Alerts
Configure Multicast
Learn how to configure multicast in
Prisma SD-WAN
.Where Can I Use
This? | What Do I
Need? |
---|---|
|
|
Prisma SD-WAN
extends the capabilities of
the Layer 3 LAN interface to include multicast. Multicasting is a
well-known one-to-many or many-to-many distributed form of network
communication. It allows the sender to send single examples of the
data packet as streams and distribute those packets only to the
hosts interested in receiving that traffic.Configure LAN
multicast on branch site devices running versions 5.6.1 or higher
than 5.6.1 but lower than 6.0.1. Configure LAN and/or WAN multicast
on devices running 6.0.1 or later versions.
- Configure multicast on branch ION devices.
- Select.WorkflowsDevicesClaimed DevicesConfigure the device
- On theBasic Infoscreen, toggleYesforEnable L3 Direct Private WAN ForwardingandEnable L3 LAN ForwardingthenSave.
- Select theInterfacestab.
- Select a port that connects to LAN.
- SelectYesforAdmin Up.
- (Optional)Enter aDescriptionand addTags.
- SelectPortas theInterfacetype.
- ForUse This Port For, selectLAN.
- ToggleScopeas eitherGlobalorLocal.
- SelectIPv4 Configurationas eitherDHCPorStatic.
- (Optional)InAdvanced Options, selectYesforMULTICASTand select anIGMP VERSIONfrom the list.Internet group management protocol (IGMP) version, the routers regularly send queries to determine which groups are active/inactive in an appropriate LAN segment.Prisma SD-WANION devices support only IGMPv2 and IGMPv3 receivers.
- (Optional)Enter a value for theInterface DR Priority.You can enter a value forInterface DR Priorityat the interface level to override the device DR Priority. The default value ofInterface DR Priorityis 1 which indicates that the ION device has an equal chance of being elected as the Designated Router (DR). Increase the value to increase the possibility of the ION device being elected as a DR.You can configureInterface DR Priorityfor devices running software versions 6.0.1 or higher.
- (Optional)ForIGMP Static Joins, enter the multicast stream source IP address and the multicast group address.You can configureIGMP Static Joinsfor devices running software versions 6.0.1 or higher.
- Save Port.
- Configure multicast on data center ION devices.
- Select.WorkflowsDevicesClaimed DevicesConfigure the device
- Select theInterfacestab.
- SelectPortas theInterfacetype.
- SelectPeer with a NetworkforUse this Port For.
- ExpandAdvanced Options.
- SelectYesforMulticast.
- (Optional)Enter a value for theInterface DR Priority.You can enter a value forInterface DR Priorityat the interface level to override the device DR Priority. The default value ofInterface DR Priorityis 1 which indicates that the ION device has an equal chance of being elected as the Designated Router (DR). Increase the value to increase the possibility of the ION device being elected as a DR.
- ClickSave Port.