: Network > Routing > Logical Routers > OSPF
Focus
Focus

Network > Routing > Logical Routers > OSPF

Table of Contents

Network > Routing > Logical Routers > OSPF

Description of OSPF fields for a logical router on an Advanced Routing Engine.
The table describes the settings to configure OSPFv2 areas for a logical router on an Advanced Routing Engine.
OSPF Settings
Description
Enable
Enable OSPF for the logical router.
Router ID
Enter a router ID in the format of an IPv4 address.
BFD Profile
If you want to apply Bidirectional Forwarding Detection to OSPF, select a BFD profile or create a new one. Default is None (Disable BFD).
Global General Timer
Select a Global Timer profile or create a new one to apply to OSPF.
Global Interface Timer
Select an OSPF Interface Timer or create a new one to apply to OSPF.
Redistribution Profile
Select an OSPF Redistribution profile or create a new one to redistribute IPv4 static routes, connected routes, IPv4 BGP routes, or the IPv4 default route to the OSPF link-state database.
Area
Area ID
Add an area identified by its Area ID in x.x.x.x format. This is the identifier that each neighbor must accept to be part of the same area.
Type
Authentication
Select an Authentication profile or create a new one.
Type
Select the type of OSPF area:
  • Normal—There are no restrictions; the area can carry all types of routes.
  • Stub—There is no outlet from the area. To reach a destination outside of the area, traffic must go through an Area Border Router (ABR), which connects to other areas.
  • NSSA (Not-So-Stubby-Area)—Traffic can leave the area only by routes other than OSPF routes.
no-summary
(Stub and NSSA areas only) Select to prevent the area from receiving Type 3 Summary LSAs and thereby reduce traffic in the area.
Default information originate
(NSSA areas only) Select to cause OSPF to originate a default route.
Metric
(NSSA areas only) Enter a metric for the default route; range is 1 to 16,777,214; default is 10.
Metric-type
(NSSA areas only) Type 1 or Type 2
ABR
Select if the logical router is an Area Border Router, which allows the next four fields to be configured.
Import-list
Select an access list or create a new one to filter network routes coming into the area based on IPv4 source address.
Export-list
Select an access list or create a new one to filter network routes that originated in the area, to allow or prevent the routes from being advertised to other areas.
Inbound Filter-List
Select a prefix list or create a new one to filter network prefixes coming into the area.
Outbound Filter-List
Select a prefix list or create a new one to filter network prefixes that originated in the area, to prevent the routes from being advertised to other areas.
IPv4 Prefix
(NSSA areas only) If ABR is selected and area type is NSSA, Add an IPv4 prefix to summarize a group of external subnets into a single Type-7 LSA, which is then translated to a Type-5 LSA and advertised to the backbone when you select Advertise.
Range
IP Address/Netmask
Add an IP Address/Netmask. A Type-3 Summary LSA (link-state advertisement) with routing information matching this range is announced into the backbone area if the area contains at least one intra-area network (that is, described with router or network LSA) from this range).
Substitute
Enter a substitute IPaddress/netmask so that a Type-3 Summary LSA with this IP address/netmask is announced into the backbone if the area contains at least one intra-area network from the IP Address/netmask specified.
Advertise
Select to send LSAs that match the subnet.
Interface
Interface
Add each interface to be included in the area.
Enable
Enable the interface.
MTU Ignore
Select to ignore maximum transmission unit (MTU) mismatches when trying to establish an adjacency (default is disabled; MTU match checking occurs). RFC 2328 defines the interface MTU as “The size in bytes of the largest IP datagram that can be sent out the associated interface, without fragmentation.”
Passive
Select to prevent the interface from sending or receiving OSPF packets; however, the interface is still included in the link-state database. You can make an interface passive, for example, if it connects to a switch, because you don’t want to send Hello packets where there is no router.
Link Type
Select the link type:
  • Broadcast—All neighbors that are accessible through the interface are discovered automatically by multicasting OSPF Hello messages, such as an Ethernet interface.
  • p2p (point-to-point)—Automatically discover the neighbor.
  • p2mp (point-to-multipoint)—Neighbors must be defined manually: Add the Neighbor IP address for all neighbors that are reachable through this interface and the Priority of each neighbor; range is 0 to 255; default is 1.
Priority
Enter the priority for the interface; the priority for the router to be elected as a designated router (DR) or backup DR (BDR); range is 0 to 255; default is 1. If zero is configured, the router will not be elected as DR or BDR.
Timer Profile
Select a Timer Profile or create a new one to apply to the interface. This profile overrides the Global Interface Timer profile applied to OSPF.
Authentication
Select an Authentication Profile or create a new one to apply to the interface. This profile overrides the Authentication profile applied on the Type tab.
BFD Profile
Select a BFD Profile or Inherit-vr-global-setting (default) or create a new BFD profile or select None (Disable BFD). This profile overrides the profile configured for OSPF.
Cost
Specify a cost for the interface; range is 1 to 65,535; default is 10.
Virtual Link
Name
Enter a name for the virtual link.
Enable
Enable the virtual link.
Area
Router ID
Timer Profile
Select a Timer Profile or create a new one to apply to the virtual link. This profile overrides the Global Interface Timer profile applied to OSPF.
Authentication
Select an Authentication Profile or create a new one to apply to the virtual link. This profile overrides the Authentication profile applied on the Type tab.
Advanced
rfc-1583 compatibility
Select to enforce compatibility with RFC 1583, which allows one best route to an autonomous system boundary router (ASBR) in the OSPF routing table. Default is disabled, which means the OSPF routing table can maintain multiple intra-AS paths in the routing table, thereby preventing routing loops.
Graceful Restart—Enable Graceful Restart
Enable Graceful Restart for the logical router; default is enabled.
Enable Helper Mode
Enable Graceful Restart Helper Mode for the logical router; default is enabled.
Enable Strict LSA Checking
Enable Strict LSA Checking to cause the helper router to stop performing helper mode and causes the graceful restart process to stop if a link-state advertisement indicates a network topology change; default is enabled.
Grace Period (sec)
Specify the number of seconds within which the logical router will perform a graceful restart if the firewall goes down or becomes unavailable. Range is 5 to 1,800; default is 120.
Max Neighbor Restart Time (sec)
Range is 5 to 1,800; default is 140.