Deploy Panorama M-Series Appliances with Local Log Collectors
Table of Contents
9.1 (EoL)
Expand all | Collapse all
-
- Determine Panorama Log Storage Requirements
-
- Setup Prerequisites for the Panorama Virtual Appliance
- Perform Initial Configuration of the Panorama Virtual Appliance
- Set Up The Panorama Virtual Appliance as a Log Collector
- Set Up the Panorama Virtual Appliance with Local Log Collector
- Set up a Panorama Virtual Appliance in Panorama Mode
- Set up a Panorama Virtual Appliance in Management Only Mode
-
- Preserve Existing Logs When Adding Storage on Panorama Virtual Appliance in Legacy Mode
- Add a Virtual Disk to Panorama on an ESXi Server
- Add a Virtual Disk to Panorama on vCloud Air
- Add a Virtual Disk to Panorama on AWS
- Add a Virtual Disk to Panorama on Azure
- Add a Virtual Disk to Panorama on Google Cloud Platform
- Add a Virtual Disk to Panorama on KVM
- Add a Virtual Disk to Panorama on Hyper-V
- Mount the Panorama ESXi Server to an NFS Datastore
-
- Increase CPUs and Memory for Panorama on an ESXi Server
- Increase CPUs and Memory for Panorama on vCloud Air
- Increase CPUs and Memory for Panorama on AWS
- Increase CPUs and Memory for Panorama on Azure
- Increase CPUs and Memory for Panorama on Google Cloud Platform
- Increase CPUs and Memory for Panorama on KVM
- Increase CPUs and Memory for Panorama on Hyper-V
- Complete the Panorama Virtual Appliance Setup
-
- Convert Your Evaluation Panorama to a Production Panorama with Local Log Collector
- Convert Your Evaluation Panorama to a Production Panorama without Local Log Collector
- Convert Your Evaluation Panorama to VM-Flex Licensing with Local Log Collector
- Convert Your Evaluation Panorama to VM-Flex Licensing without Local Log Collector
- Convert Your Production Panorama to an ELA Panorama
-
- Register Panorama
- Activate a Panorama Support License
- Activate/Retrieve a Firewall Management License when the Panorama Virtual Appliance is Internet-connected
- Activate/Retrieve a Firewall Management License when the Panorama Virtual Appliance is not Internet-connected
- Activate/Retrieve a Firewall Management License on the M-Series Appliance
- Install the Panorama Device Certificate
-
- Migrate from a Panorama Virtual Appliance to an M-Series Appliance
- Migrate a Panorama Virtual Appliance to a Different Hypervisor
- Migrate from an M-Series Appliance to a Panorama Virtual Appliance
- Migrate from an M-100 Appliance to an M-500 Appliance
- Migrate from an M-100 or M-500 Appliance to an M-200 or M-600 Appliance
-
- Configure an Admin Role Profile
- Configure an Access Domain
-
- Configure a Panorama Administrator Account
- Configure Local or External Authentication for Panorama Administrators
- Configure a Panorama Administrator with Certificate-Based Authentication for the Web Interface
- Configure an Administrator with SSH Key-Based Authentication for the CLI
- Configure RADIUS Authentication for Panorama Administrators
- Configure TACACS+ Authentication for Panorama Administrators
- Configure SAML Authentication for Panorama Administrators
-
- Add a Firewall as a Managed Device
-
- Add a Device Group
- Create a Device Group Hierarchy
- Create Objects for Use in Shared or Device Group Policy
- Revert to Inherited Object Values
- Manage Unused Shared Objects
- Manage Precedence of Inherited Objects
- Move or Clone a Policy Rule or Object to a Different Device Group
- Push a Policy Rule to a Subset of Firewalls
- Manage the Rule Hierarchy
- Manage the Master Key from Panorama
- Redistribute User-ID Information to Managed Firewalls
-
- Plan the Transition to Panorama Management
- Migrate a Firewall to Panorama Management and Reuse Existing Configuration
- Migrate a Firewall to Panorama Management and Push a New Configuration
- Migrate a Firewall HA Pair to Panorama Management and Reuse Existing Configuration
- Migrate a Firewall HA Pair to Panorama Management and Push a New Configuration
- Load a Partial Firewall Configuration into Panorama
- Localize a Panorama Pushed Configuration on a Managed Firewall
-
- Add Standalone WildFire Appliances to Manage with Panorama
- Configure Basic WildFire Appliance Settings on Panorama
- Remove a WildFire Appliance from Panorama Management
-
-
- Configure a Cluster and Add Nodes on Panorama
- Configure General Cluster Settings on Panorama
- Remove a Cluster from Panorama Management
- Configure Appliance-to-Appliance Encryption Using Predefined Certificates Centrally on Panorama
- Configure Appliance-to-Appliance Encryption Using Custom Certificates Centrally on Panorama
- View WildFire Cluster Status Using Panorama
- Upgrade a Cluster Centrally on Panorama with an Internet Connection
- Upgrade a Cluster Centrally on Panorama without an Internet Connection
-
-
- Manage Licenses on Firewalls Using Panorama
-
- Supported Updates
- Schedule a Content Update Using Panorama
- Upgrade Log Collectors When Panorama Is Internet-Connected
- Upgrade Log Collectors When Panorama Is Not Internet-Connected
- Upgrade Firewalls When Panorama Is Internet-Connected
- Upgrade Firewalls When Panorama Is Not Internet-Connected
- Upgrade a ZTP Firewall
- Revert Content Updates from Panorama
-
- Preview, Validate, or Commit Configuration Changes
- Enable Automated Commit Recovery
- Compare Changes in Panorama Configurations
- Manage Locks for Restricting Configuration Changes
- Add Custom Logos to Panorama
- Use the Panorama Task Manager
- Reboot or Shut Down Panorama
- Configure Panorama Password Profiles and Complexity
-
-
- Verify Panorama Port Usage
- Resolve Zero Log Storage for a Collector Group
- Replace a Failed Disk on an M-Series Appliance
- Replace the Virtual Disk on an ESXi Server
- Replace the Virtual Disk on vCloud Air
- Migrate Logs to a New M-Series Appliance in Log Collector Mode
- Migrate Logs to a New M-Series Appliance in Panorama Mode
- Migrate Logs to a New M-Series Appliance Model in Panorama Mode in High Availability
- Migrate Logs to the Same M-Series Appliance Model in Panorama Mode in High Availability
- Migrate Log Collectors after Failure/RMA of Non-HA Panorama
- Regenerate Metadata for M-Series Appliance RAID Pairs
- Troubleshoot Registration or Serial Number Errors
- Troubleshoot Reporting Errors
- Troubleshoot Device Management License Errors
- Troubleshoot Automatically Reverted Firewall Configurations
- Complete Content Update When Panorama HA Peer is Down
- View Task Success or Failure Status
- Restore an Expired Device Certificate
- Downgrade from Panorama 9.1
End-of-Life (EoL)
Deploy Panorama M-Series Appliances with Local Log Collectors
The following figures illustrate Panorama
in a centralized log collection deployment. In these examples, the
Panorama management server comprises two M-Series appliances in
Panorama mode that are deployed in an active/passive high availability
(HA) configuration. The firewalls send logs to the predefined (default)
local Log Collector on each Panorama M-Series appliance. This is
the recommended deployment if the firewalls generate up to 10,000
logs/second.
If you will assign more
than one Log Collector to a Collector Group, see Caveats
for a Collector Group with Multiple Log Collectors to understand
the requirements, risks, and recommended mitigations.
After
implementing this deployment, if the logging rate increases beyond 10,000
logs per second, Palo Alto Networks recommends that you add Dedicated
Log Collectors (M-Series appliances in Log Collector mode) as described
in Deploy
Panorama with Dedicated Log Collectors. Such an expansion
might require reassigning firewalls from the local Log Collectors
to Dedicated Log Collectors.
Perform
the following steps to deploy Panorama with local Log Collectors. Skip
any steps you have already performed (for example, the initial setup).
- Perform the initial setup of each M-Series appliance.
- Rack mount the M-Series appliance. Refer to the M-Series Hardware Reference Guides for instructions.
- Perform
Initial Configuration of the M-Series Appliance.Palo Alto Networks recommends reserving the management (MGT) interface for administrative access to Panorama and dedicating separate M-Series Appliance Interfaces to other Panorama services.
- Configure each array. This task is required to make the RAID disks available for logging. Optionally, you can add disks to Increase Storage on the M-Series Appliance.
- Register Panorama and Install Licenses.
- Install Content and Software Updates for Panorama.
- Set Up HA on Panorama.
- Perform the following steps to prepare Panorama for log
collection.
- Connect to the primary Panorama in one of
the following ways:
- Attach a serial cable from your computer to the Console port on the primary Panorama. Then use terminal emulation software (9600-8-N-1) to connect.
- Use terminal emulation software such as PuTTY to open an SSH session to the IP address that you specified for the MGT interface of the primary Panorama during initial configuration.
- Log in to the CLI when prompted. Use the default admin account and the password that you specified during initial configuration.
- Enable the primary Panorama to connect to the secondary
Panorama by entering the following command, where <IPaddress2> represents the
MGT interface of the secondary Panorama:
> configure # set deviceconfig system panorama-server <IPaddress2> # commit
- Log in to the CLI of the secondary Panorama.
- Enable the secondary Panorama to connect to the primary
Panorama by entering the following command, where <IPaddress1> represents the
MGT interface of the primary Panorama:
> configure # set deviceconfig system panorama-server <IPaddress1> # commit # exit
- In the CLI of the secondary Panorama, enter the following
command to display the serial number, and then record it:
> show system info | match serial
You need the serial number to add the Log Collector of the secondary Panorama as a managed collector to the primary Panorama.
- Connect to the primary Panorama in one of
the following ways:
- Edit the Log Collector that is local to the primary Panorama.Use the web interface of the primary Panorama to perform these steps:
- Select PanoramaManaged Collectors and select the default (local) Log Collector.
- Select Disks and Add each logging disk pair.
- Click OK to save your changes.
- Configure the Log Collector that is local to the secondary
Panorama.Panorama treats this Log Collector as remote because it’s not local to the primary Panorama. Therefore you must manually add it on the primary Panorama.Use the web interface of the primary Panorama to Configure a Managed Collector:
- Select PanoramaManaged Collectors and Add the Log Collector.
- Enter the serial number (Collector S/N) you recorded for the Log Collector of the secondary Panorama.
- Enter the IP address or FQDN of the primary and secondary
Panorama HA peers in the Panorama Server IP field
and Panorama Server IP 2 field respectively.Both of these fields are required.
- Select Interfaces and configure
each interface that the Log Collector will use. The Management interface
is required. Perform the following steps for each interface:
- Click the interface name.
- Configure one or both of the following field sets based on the IP protocols of your network.IPv4—IP Address, Netmask, and Default GatewayIPv6—IPv6 Address/Prefix Length and Default IPv6 Gateway
- (Management interface only) Select SNMP if you will use an SNMP manager to monitor Log Collector statistics.Using SNMP requires additional steps besides configuring the Log Collector (see Monitor Panorama and Log Collector Statistics Using SNMP).
- Click OK to save your changes to the interface.
- Click OK to save your changes to the Log Collector.
- Select CommitCommit to Panorama and Commit your changes.This step is required before you can enable logging disks.
- Edit the Log Collector by clicking its name.
- Select Disks, Add each RAID disk pair, and click OK.
- Select CommitCommit to Panorama and Commit your changes.
- Add
a Firewall as a Managed Device.Use the web interface of the primary Panorama to perform this task for each firewall that will forward logs to the Log Collectors.
- Edit the default Collector Group that is predefined on
the primary Panorama.Use the web interface of the primary Panorama to Configure a Collector Group:
- Select PanoramaCollector Groups and edit the default Collector Group.
- Add the local Log Collector
of the secondary Panorama to the Collector Group Members list if
you are adding multiple Log Collectors to a single Collector group.
By default, the list displays the local Log Collector of the primary
Panorama because it is pre-assigned to the default Collector Group.In any single Collector Group, all the Log Collectors must run on the same Panorama model: all M-600 appliances, all M-500 appliances, all M-200 appliances, all M-100 appliances, or all Panorama virtual appliances.
- (Best Practice) Enable log redundancy across collectors if you add multiple Log Collectors to a single Collector group. This option requires each Log Collector to have the same number of logging disks.
- (Optional) Select Monitoring and configure the settings if you will use SNMP to monitor Log Collector statistics and traps.
- Select Device Log Forwarding and
configure the Log Forwarding Preferences list. This list defines
which firewalls forward logs to which Log Collectors. Assign firewalls
according to the number of Log Collectors in this Collector Group:
- Single—Assign the firewalls that will forward logs to the local Log Collector of the primary Panorama, as illustrated in Single Local Log Collector Per Collector Group.
- Multiple—Assign each firewall to both Log Collectors for redundancy. When you configure the preferences, make Log Collector 1 the first priority for half the firewalls and make Log Collector 2 the first priority for the other half, as illustrated in Multiple Local Log Collectors Per Collector Group.
- Click OK to save your changes.
- Configure a Collector Group that contains the Log Collector
of the secondary Panorama.Required if each Collector Group has only one Log Collector.Use the web interface of the primary Panorama to Configure a Collector Group:
- Select PanoramaCollector Groups and Add the Collector Group.
- Enter a Name to identify the Collector Group.
- Add the local Log Collector of the secondary Panorama to the Collector Group Members list.
- (Optional) Select Monitoring and configure the settings if you will use an SNMP manager to monitor Log Collector statistics and traps.
- Select Device Log Forwarding and Add an
entry to the Log Forwarding Preferences list:
- Modify the Devices list, select the firewalls that will forward logs to the local Log Collector of the secondary Panorama (see Single Local Log Collector Per Collector Group), and click OK.
- Add the local Log Collector of the secondary Panorama to the Collectors list and click OK.
- Click OK to save your changes.
- Commit and push your changes to the Panorama configuration
and the Collector Groups.In the web interface of the primary Panorama, select CommitCommit and Push and then Commit and Push your changes to Panorama and the Collector Groups you added.
- Manually fail over so that the secondary Panorama becomes
active.Use the web interface of the primary Panorama to perform the following steps:
- Select PanoramaHigh Availability.
- Click Suspend local Panorama in the Operational Commands section.
- On the secondary Panorama, configure the network settings
of the Log Collector that is local to the primary Panorama.Use the web interface of the secondary Panorama to perform the following steps:
- In the Panorama web interface, select PanoramaManaged Collectors and select the Log Collector that is local to the primary Panorama.
- Enter the IP address or FQDN of the primary and secondary
Panorama HA peers in the Panorama Server IP field
and Panorama Server IP 2 field respectively.Both of these fields are required.
- Select Interfaces, click Management,
and complete one or both of the following field sets (based on the
IP protocols of your network) with the MGT interface values of the
primary Panorama:
- IPv4—IP Address, Netmask, and Default Gateway
- IPv6—IPv6 Address/Prefix Length and Default IPv6 Gateway
- Click OK to save your changes.
- Select CommitCommit and Push and then Commit and Push your changes to Panorama and the Collector Groups you added.
- Manually fail back so that the primary Panorama becomes
active.Use the web interface of the secondary Panorama to perform the following steps:
- Select PanoramaHigh Availability.
- Click Suspend local Panorama in the Operational Commands section.
- Configure log forwarding from firewalls to Panorama.Use the web interface of the primary Panorama to:
- Configure Log Forwarding to Panorama.
- Verify Log Forwarding to Panorama.
- (Optional) Configure
Log Forwarding from Panorama to External Destinations.You can assign separate external server profiles to each Panorama HA peer. For example, you might want each peer to forward logs to a different syslog server. To make each Panorama peer forward logs to different external services, log in to the web interface of each peer, select PanoramaCollector Groups, select the Collector Group, select Collector Log Forwarding, assign the server profiles, and click OK.