Add Performance Policy SLA
Table of Contents
Expand all | Collapse all
-
-
- Add a Branch
- Add a Data Center
- Add a Branch Gateway
- Configure Circuits
- Configure Internet Circuit Underlay Link Aggregation
- Configure Private WAN Underlay Link Quality Aggregation
- Configure Circuit Categories
- Configure Device Initiated Connections for Circuits
- Add Public IP LAN Address to Enterprise Prefixes
- Manage Data Center Clusters
- Configure a Site Prefix
- Configure a DHCP Server
- Configure NTP for Prisma SD-WAN
- Configure the ION Device at a Branch Site
- Configure the ION Device at a Data Center
- Switch a Site to Control Mode
- Allow IP Addresses in Firewall Configuration
-
- Configure a Controller Port
- Configure Internet Ports
- Configure WAN/LAN Ports
- Configure a Loopback Interface
- Configure a PoE Port
- Configure and Monitor LLDP Activity and Status
- Configure a PPPoE Interface
- Configure a Layer 3 LAN Interface
- Configure Application Reachability Probes
- Configure a Secondary IP Address
- Configure a Static ARP
- Configure a DHCP Relay
- Configure IP Directed Broadcast
- VPN Keep-Alives
-
- Configure Prisma SD-WAN IPFIX
- Configure IPFIX Profiles and Templates
- Configure and Attach a Collector Context to a Device Interface in IPFIX
- Configure and Attach a Filter Context to a Device Interface in IPFIX
- Configure Global and Local IPFIX Prefixes
- Flow Information Elements
- Options Information Elements
- Configure the DNS Service on the Prisma SD-WAN Interface
- Configure SNMP
-
-
- Prisma SD-WAN Branch Routing
- Prisma SD-WAN Data Center Routing
-
- Configure Multicast
- Create a WAN Multicast Configuration Profile
- Assign WAN Multicast Configuration Profiles to Branch Sites
- Configure a Multicast Source at a Branch Site
- Configure Global Multicast Parameters
- Configure a Multicast Static Rendezvous Point (RP)
- Learn Rendezvous Points (RPs) Dynamically
- View LAN Statistics for Multicast
- View WAN Statistics for Multicast
- View IGMP Membership
- View the Multicast Route Table
- View Multicast Flow Statistics
- View Routing Statistics
- Prisma SD-WAN Incident Policies
-
- Prisma SD-WAN Branch HA Key Concepts
- Configure Branch HA
- Configure HA Groups
- Add ION Devices to HA Groups
- View Device Configuration of HA Groups
- Edit HA Groups and Group Membership
-
- Configure Branch HA with Gen-1 Platforms (2000, 3000, 7000, and 9000)
- Configure Branch HA with Gen-2 Platforms (3200, 5200, and 9200)
- Configure Branch HA with Gen-2 Embedded Switch Platforms (1200-S or 3200-L2)
- Configure Branch HA for Devices with Software Cellular Bypass (1200-S-C-5G)
- Configure Branch HA for Platforms without Bypass Pairs
- Prisma SD-WAN Clarity Reports
- Prisma SD-WAN Incidents and Alerts
Add Performance Policy SLA
Steps to add performance policy SLAs that provide latency, packet loss, and jitter
thresholds.
Where Can I Use This? | What Do I Need? |
---|---|
|
|
The
Performance SLAs
tab contains Prisma SD-WAN performance
SLAs. It provides the Application, Link Quality Metrics, System Health, Circuit
Utilization, Flow and, Probe SLA threshold values for the performance policy rule. Use the
Actions
icons to Edit
a performance SLA, view the audit logs for any system configuration
changes, or remove a performance SLA. To add a performance SLA:
- Go toand selectManagePoliciesPerformancePerformance SLAsAdd New SLA.
- In theAdd New Performance SLAscreen, enter aNamefor the SLA with the option of including a description and tags.
- Select the desiredMetricsfrom the drop-down.
- If you check the optionLink Quality Metrics,
- Enter theLatencyvalue (between 1-500ms).
- Continue to click the + sign or select from the drop-down to enter theJittervalue (between 1-100ms), theMOSvalue (between 1-5), and thePacket Lossvalue (between 1-20%).
On a per-branch circuit basis, the Jitter, Latency and Packet Loss values will utilize the best (lowest) measured value between the Branch and all Data Centers. - If you check the optionApplication Metrics,
- Provide theInit Failure Rate(between 1-100%).
- Continue to click the + sign or select from the drop-down to enter theRTTvalue (between 1-500ms) and theUDP TRTvalue (between 1-500ms).Init Failure rate is the percentage of TCP 3-way handshake failures and RTT is the TCP Round Trip Time from a client to the server and back to the client.UDP Response Time (UDP-TRT) is the amount of time it takes for the server to respond to the UDP transaction request from the time the request is received. Currently, UDP-TRT provides information on UDP DNS traffic only.
- If you check theProbeoption,
- Select theProbeconfig from the drop-down. Depending on the probe config selected (DNS/HTTP/ICMP), enter the value for the following probe metrics:
- DNS Transaction Time(between 1-500ms), and theDNS Transaction Failure Rate(between 1-100%).
- HTTP Transaction Time(between 1-500ms), andInit Failure Rate(between 1-100%).
- Latencyvalue (between 1-500ms), and continue to click the + sign or select from the drop-down to enter theJittervalue (between 1-100ms) and thePacket Lossvalue (between 1-20%).
- If you check the optionSystem Health Metrics,
- Enter theCPU Utilizationvalue (between 1-100%).
- Continue to click the + sign or select from the drop-down to enter theMemory Utilizationvalue (between 1-100%) and theDisk Utilizationvalue (between 1-100%).
- If you check the optionCircuit Utilization, enter theCircuit Utilizationvalue (between 1-100%).
- If you check the optionFlow Metrics, enter theConcurrent Flow Utilizationvalue (between 1-100%).
- Save your changes.