Add Performance Policy Stack
Table of Contents
Expand all | Collapse all
-
-
- Add a Branch
- Add a Data Center
- Add a Branch Gateway
- Configure Circuits
- Configure Internet Circuit Underlay Link Aggregation
- Configure Private WAN Underlay Link Quality Aggregation
- Configure Circuit Categories
- Configure Device Initiated Connections for Circuits
- Add Public IP LAN Address to Enterprise Prefixes
- Manage Data Center Clusters
- Configure a Site Prefix
- Configure a DHCP Server
- Configure NTP for Prisma SD-WAN
- Configure the ION Device at a Branch Site
- Configure the ION Device at a Data Center
- Switch a Site to Control Mode
- Allow IP Addresses in Firewall Configuration
-
- Configure a Controller Port
- Configure Internet Ports
- Configure WAN/LAN Ports
- Configure a Loopback Interface
- Configure a PoE Port
- Configure and Monitor LLDP Activity and Status
- Configure a PPPoE Interface
- Configure a Layer 3 LAN Interface
- Configure Application Reachability Probes
- Configure a Secondary IP Address
- Configure a Static ARP
- Configure a DHCP Relay
- Configure IP Directed Broadcast
- VPN Keep-Alives
-
- Configure Prisma SD-WAN IPFIX
- Configure IPFIX Profiles and Templates
- Configure and Attach a Collector Context to a Device Interface in IPFIX
- Configure and Attach a Filter Context to a Device Interface in IPFIX
- Configure Global and Local IPFIX Prefixes
- Flow Information Elements
- Options Information Elements
- Configure the DNS Service on the Prisma SD-WAN Interface
- Configure SNMP
-
-
- Prisma SD-WAN Branch Routing
- Prisma SD-WAN Data Center Routing
-
- Configure Multicast
- Create a WAN Multicast Configuration Profile
- Assign WAN Multicast Configuration Profiles to Branch Sites
- Configure a Multicast Source at a Branch Site
- Configure Global Multicast Parameters
- Configure a Multicast Static Rendezvous Point (RP)
- Learn Rendezvous Points (RPs) Dynamically
- View LAN Statistics for Multicast
- View WAN Statistics for Multicast
- View IGMP Membership
- View the Multicast Route Table
- View Multicast Flow Statistics
- View Routing Statistics
- Prisma SD-WAN Incident Policies
-
- Prisma SD-WAN Branch HA Key Concepts
- Configure Branch HA
- Configure HA Groups
- Add ION Devices to HA Groups
- View Device Configuration of HA Groups
- Edit HA Groups and Group Membership
-
- Configure Branch HA with Gen-1 Platforms (2000, 3000, 7000, and 9000)
- Configure Branch HA with Gen-2 Platforms (3200, 5200, and 9200)
- Configure Branch HA with Gen-2 Embedded Switch Platforms (1200-S or 3200-L2)
- Configure Branch HA for Devices with Software Cellular Bypass (1200-S-C-5G)
- Configure Branch HA for Platforms without Bypass Pairs
- Prisma SD-WAN Clarity Reports
- Prisma SD-WAN Incidents and Alerts
Add Performance Policy Stack
Steps to add a simple and advanced performance policy stack in SD-WAN.
Where Can I Use This? | What Do I Need? |
---|---|
|
|
The
Performance Policy Stacks
is a collection of performance
sets containing the performance policy rules. Performance policy sets specify
traffic engineering and can accommodate a maximum of four policy sets and one
default rule policy set for each policy stack. The
Performance Stacks
tab lists the existing policy stacks. Use the
Actions
icons to Edit, attach the policy to a site, view the
audit logs or any system configuration
changes, and remove a policy stack.To add a performance stack is a collection of policy rules in a single
policy set:
- Select.ManagePoliciesPerformancePerformance Stacks
- SelectSimple or AdvancedandAdd Stack.
- On theAdd New Performance Stackscreen, enter aNamefor the stack, and optionallyDescriptionandTags.
- InAdvancedUI, assign performance sets to the policy stack by selecting from thePolicy Setsdrop down.The policy sets in a stack are ordered from left to right, with the left-most policy set designated as the highest priority.
- Save to add to the stacks.