Return the ION Device to Prisma SD-WAN
Table of Contents
Expand all | Collapse all
-
-
- Add a Branch
- Add a Data Center
- Add a Branch Gateway
- Configure Circuits
- Configure Internet Circuit Underlay Link Aggregation
- Configure Private WAN Underlay Link Quality Aggregation
- Configure Circuit Categories
- Configure Device Initiated Connections for Circuits
- Add Public IP LAN Address to Enterprise Prefixes
- Manage Data Center Clusters
- Configure a Site Prefix
- Configure a DHCP Server
- Configure NTP for Prisma SD-WAN
- Configure the ION Device at a Branch Site
- Configure the ION Device at a Data Center
- Switch a Site to Control Mode
- Allow IP Addresses in Firewall Configuration
-
- Configure a Controller Port
- Configure Internet Ports
- Configure WAN/LAN Ports
- Configure a Loopback Interface
- Configure a PoE Port
- Configure and Monitor LLDP Activity and Status
- Configure a PPPoE Interface
- Configure a Layer 3 LAN Interface
- Configure Application Reachability Probes
- Configure a Secondary IP Address
- Configure a Static ARP
- Configure a DHCP Relay
- Configure IP Directed Broadcast
- VPN Keep-Alives
-
- Configure Prisma SD-WAN IPFIX
- Configure IPFIX Profiles and Templates
- Configure and Attach a Collector Context to a Device Interface in IPFIX
- Configure and Attach a Filter Context to a Device Interface in IPFIX
- Configure Global and Local IPFIX Prefixes
- Flow Information Elements
- Options Information Elements
- Configure the DNS Service on the Prisma SD-WAN Interface
- Configure SNMP
-
-
- Prisma SD-WAN Branch Routing
- Prisma SD-WAN Data Center Routing
-
- Configure Multicast
- Create a WAN Multicast Configuration Profile
- Assign WAN Multicast Configuration Profiles to Branch Sites
- Configure a Multicast Source at a Branch Site
- Configure Global Multicast Parameters
- Configure a Multicast Static Rendezvous Point (RP)
- Learn Rendezvous Points (RPs) Dynamically
- View LAN Statistics for Multicast
- View WAN Statistics for Multicast
- View IGMP Membership
- View the Multicast Route Table
- View Multicast Flow Statistics
- View Routing Statistics
- Prisma SD-WAN Incident Policies
-
- Prisma SD-WAN Branch HA Key Concepts
- Configure Branch HA
- Configure HA Groups
- Add ION Devices to HA Groups
- View Device Configuration of HA Groups
- Edit HA Groups and Group Membership
-
- Configure Branch HA with Gen-1 Platforms (2000, 3000, 7000, and 9000)
- Configure Branch HA with Gen-2 Platforms (3200, 5200, and 9200)
- Configure Branch HA with Gen-2 Embedded Switch Platforms (1200-S or 3200-L2)
- Configure Branch HA for Devices with Software Cellular Bypass (1200-S-C-5G)
- Configure Branch HA for Platforms without Bypass Pairs
- Prisma SD-WAN Clarity Reports
- Prisma SD-WAN Incidents and Alerts
Return the ION Device to Prisma SD-WAN
Prisma SD-WAN
Learn how to return the ION device to
Prisma SD-WAN
.Before you remove a
device from a site, you need to remove the configuration from the device first.Where Can I Use
This? | What Do I
Need? |
---|---|
|
|
You can return an ION device to
Prisma SD-WAN
.
Before you remove a device from a site, you need to remove the configuration
from the device first, you need to specifically remove the circuits
attached to interfaces. These checks are for protection against
accidental misconfiguration.- Select.WorkflowsDevicesClaimed DevicesConfirm that the replacement device is assigned to the site and isOnline. Also, confirm that the RMA device is assigned butOffline.
- Click the ellipsis menu for the RMA device and selectUnassign device from site.
- ClickOKto confirm removal of the device from the site.The state of the device displaysUnassigning.
- (Optional)Remove circuits attached to interfaces.If you see a messageSite WAN interface id exists in this element, then go to the interface configuration and remove each of the circuits labels attached to any WAN interface of the device.
- Click the ellipsis menu and selectPut back in inventory.
- ClickOkto confirm unclaiming of the device.
- Click theUnclaimedtab to view the device.The device is offline and theStatechangesTo return.
- Click the ellipsis menu and selectReturn to Prisma SD-WAN.
- ClickReturnto confirm returning the device toPrisma SD-WAN.The device is then removed from your inventory.The device is visible underUnclaimedwith statusTo Return.
Remove circuits attached to interfaces
- Select.WorkflowsDevicesClaimed Devices
- Click the ellipsis menu for a device and selectConfigure the device.
- ClickInterfaces.
- Select an interface.
- ForCircuit Label, clickupdate.When you clickupdate, the device removes the circuits attached to the interface.
- ClickSave Port.
- Repeat these steps for all interfaces—ports or bypass pairs which have circuits attached.